10.0000 MHz TCXO 1ppm Frequency Standard & 10 MHz Crystal Set ** USA SELLER ** 海外 即決【コストコ お買い得】

10.0000 TCXO and Crystal 1217 Most purchases qualify for a ** Combined Shipping Discount ** Fast eMail Fast Shipping Guaranteed Good-on-Arrival (1) 10.0000 MHz TCXO 1ppm Precision Frequency Reference Crystal Oscillator and (1) 10.000MHzCrystal 18 pF， HC-49/UCase Listing is for (1) TCXO & Crystal Set TCXO Specifications Stability vs Temperature: ± 1ppm from 0C to +50C (operates -10C to +60C) Stability vs Aging: ± 1ppm / year Power: +5V ± 5% @ 20 mA max. Output: TTL Compatible Internal Adjustable Trimmer: ± 5ppm Datasheet for Monitor 7400B2A1: https://linearparts.com/images/7400B2A1-10MHZ-TCXO-3Y.JPG Date Code: 99xx Application Information (See pictures) This TCXO is a very stable， temperature compensated precision reference crystal oscillator. Applications include an inexpensive HAM shack Frequency Standard， internal clock timebase or external signal source for calibrating other equipment such as radios and oscilloscopes to name a few examples. Output Signal Details The output signal is a TTL compatible square wave， TP1， figure 2. You can add a low pass LC filter (not included) to remove the harmonics to produce a sine wave. A simple 10 MHz crystal filter also does a remarkably good wave-shaping job as you can see below in figure 3， TP2. In this configuration， the resonating crystal put a 20 volt peak-to-peak signal across the 10K Ohm load resistor. Replace the fixed 10K resistor with a trimmer for an adjustable output. Performance verification / calibration can be done with little more than an inexpensive AM shortwave radio capable of receiving the WWV 10 MHz broadcast. Details below. Initial Accuracy The output frequency of this TCXO (Temperature Compensated Crystal Oscillator) was factory set and should be very close. But these are "New Old Stock，" DC 99xx， and may have drifted slightly so you may want to tweak them. An internal trimmer is accessible for making minor frequency adjustments to compensate for aging. Test Equipment Options A really good lab quality frequency counter would be convenient， but if you are like me and dont have a high resolution frequency counter， you can go to Plan B and fine tune the oscillator by zero-beating it against another 10 MHz reference signal. Fortunately， this alternate calibration method of the TCXO does not even require any sophisticated equipment. All you need is an AM shortwave radio (Note 2) that can receive a good signal from the NIST 10 MHz WWV transmitter located in Boulder Colorado. NIST is the federal agency that everyone else uses to calibrate their calibrators. Cant get any better than that. Calibration Carefully remove the tape over the trimmer access hole， figure 4， and save for reuse. I used an all-metal jewelers screwdriver to tweak the frequency and surprisingly I didnt experience any frequency pull when I touched the metal blade to the metal trimmer. Tune the radio in AM mode to the 10 MHz WWV station. The stronger the signal， the better. Power up the TCXO and use a short wire， adjusting length as necessary， to produce a comparable signal strength. It may take a little experimentation to balance the signal levels of both WWV and TCXO but its really not very critical. Once you get their levels set， you can easily adjust the TCXO to a fraction of a Hertz by ear. When you are close to synchronization， you will hear a very slow pulsating or swooshing sound. This is the beat frequency difference between WWV and your TCXO and it is very recognizable when the frequency difference is several Hertz. Once you are familiar with the sound， your objective is to slow the pulsing swoosh rate down. With a little patience you can slow the pulsation period to a few seconds or even make it appear to freeze. A two second period would represent a 1/2 Hz error at 10 MHz， but remember， short term results are still subject to the frequency stability specifications shown above so it is not reasonable to expect that calibration to within a few tenths of a Hz will hold over the long term. A reasonably constant ambient temperature and a well regulated 5 Volt power source will provide best results. Ambient temperature， supply voltage and aging will cause drift but it should still be less than 1ppm. (See the specifications above.) Mounting and Wiring This device has 3 leads. Lead spacing is compatible with the standard DIP-14 IC pattern (i.e. pins 7， 8 and 14) although extra room is required for the larger footprint of the metal can. Lead length is 3/8" and can be trimmed to fit a socket or left intact for mounting on a thermal insulator. Before applying power， verify your connections with our diagram / datasheet provided above. Incorrect wiring will destroy the TCXO. Notes: 1) This listing is for the TXCO and Crystal only. The resistor is for illustration only and is NOT included. 2) The actual receiver calibration accuracy does NOT matter since you are mixing the two 10 MHz signals together and only listening for their relative difference in frequencies. FYI， 1ppm is roughly equivalent to a clock error of about 30 seconds per year. 3) The datasheet is a high resolution scan and may not display properly on some browsers. If you encounter viewing problems， download the file and open in a JPG viewer. IMPORTANT - USE OUR DIAGRAMS to wire your TCXO WARNING: Theres an INCORRECT DATASHEET on the INTERNET with a WRONG PINOUT! OUR WIRING DIAGRAMS including our datasheet link are VERIFIED and CORRECT and we test each device before shipping. Use our diagrams and you will have no problem. If you use the datasheet on the web that is wrong (pins 8 & 14 are swapped) you will destroy your TCXO! Q30X 800 pixels REVISED Rev11/05/20 added sentence to check our store for other listed quantities --> ************************************* ham radio etronic e-tronic hamtronic qba BootsParts USA boots PAYMENT and SHIPPING ** We offer a Combined Shipping Discount for most purchases (no books) if paid with ONE SINGLE PAYMENT with eBays SHOPPING CART ** Condition of Goods Unless otherwise noted above: NOS (New Old Stock) or better， clean， unused 30 day Non-DOA， Good-on-Arrival Guarantee Untested， but NO JUNK or suspect parts PCB parts are thru-hole， NO SMD/SMT Small parts may be bulk packed Manufacturers and Date Codes may vary Attention International bidders only: Sorry， we ship to US ZIP Codes ONLY. We DO NOT ship Internationally. We ONLY ship to Registered US addresses. We DO NOT accept INTERNATIONAL payments. IMPORTANT: The parts we sell are categorized as new because they are unused， but many of our parts are those rare， hard-to-find， discontinued， manufacturing surplus and / or old stock commonly known in the parts business as NOS (New Old Stock). Some of our stock pictures show date codes which may vary from the actual product shipped. Parts from a larger OEM package may be repacked for smaller lot size orders or for more practical handling and shipping. See our store for other listed quantities. We strive to give full and accurate descriptions to earn your 5-Star Feedback. Any known deficiencies are listed in the detailed description. Datasheets are provided when available. Some datasheets may be close but not a perfect match because of part revisions or because they may be from a different manufacturer. If you have any questions concerning our products please email us before purchasing. Your complete satisfaction is important to us before and after the sale. Thank you. 110520